Author Archives: admin

Garage Door Openers – I Can Not Imagine Life Without Them

A Garage door opener is a piece of equipment used for opening and closing garage doors. Most models are remote controlled. Garage door openers are simple but extremely useful devices. So much so, that it’s hard to imagine living without them now.

The first garage door opener consisted of a radio transmitter, a receiver and an actuator to open or close the door. In this the receiver would detect a change in the amplitude and would open or close the door. However there was a security concern with these kinds of garage door openers. They could be opened by anybody with a transmitter. Also there were accidental openings of garage doors by neighbors trying to open their doors. The later door openers used a shared frequency to overcome the accidental opening by other users. Using dipswitches a total of 256 combinations were made to prevent interference from other garage door openers. However the security issue was still not overcome.

The present day garage door openers use rolling frequency or hopping code technology. In these the frequency of opening is look ahead type, that means every time the door is opened then the next time the door will be opened by another frequency.

The technology for garage door openers is fairly simple. Three kinds are used, chain drive, screw drive and belt drive. Chain drives are noisy as they use a metallic chain along with a metal trolley. However they are fairly cheap about $130 Screw drives consists of a threaded lead screw. They start at about $150 The newer models consist of plastic lined tracks to reduce the noise and increase the speed of opening. Belt drives are the costliest and the quietest. They begin at about $170.

There is a misconception that the lifting is done by the door opener. However the actual lifting is done by the springs. When the door is closed the springs come into tension. When the door is being opened the spring does most of the lifting. There are two types linear expansion springs and torsional springs. Garage door openers are of two types, jackshaft type and trolley type. The jackshaft type occupies less space. The trolley type consists of trolley attached to the door and also to the motor. This occupies space in the ceiling but is more popular because it is safer. In jackshaft type, it is difficult to sense when someone is being crushed under the door. There are two types of motors available, AC and DC. AC is more common but DC has many advantages. It consumes less electricity, the speed is easily controlled and makes less noise.

There are some models which auto reverse incase of obstruction like a pet or a child. The remotes usually operate up to a distance of 150 feet. The remote can be used to switch on the light of the garage also. Most garage door openers come with a keypad, which can be installed outside the garage. This is used to open the garage, if the remote batteries are down or the user has forgotten the remote. Most garage door openers allow emergency release so that the door can be opened manually in case of power failures.

Garage Door Repair – 5 Simple Things to Check

Here in San Diego, you have many choices in San Diego Garage Door Repair. I found this article about Garage Door Repair that might help you make the decision on who to call. No matter what area of San Diego you are in, call us at All American Garage!

Garage door repair may often be done by the homeowner themselves. There are at least 5 simple things to check, before calling a professional. Some repairs are extremely easy. For example, a stiff or a squeaky door will merely require a good cleaning and lubrication. Other repairs, such as repairing a torsion spring, are extremely dangerous and require help from a professional.

Before proceeding to the repair, make sure to unplug your garage door opener, so that you do not get an electric shock while you are repairing your garage door. You will most likely be standing on a ladder, which is a very bad place to get an electric shock, since you may also fall off the ladder. Also, remember to wear safety glasses when working with power tools.

Here is a list of things to check before calling for a professional for your garage door repair:

1. Check the Metal Tracks for Damages

This easy garage door repair tip may often solve the problem very fast. The metal tracks often may have dents or bumps. If you find any such damages, strike the damaged part of the track with a wood block and a hammer to straighten the track.

2. Check the Alignment of the Tracks

If the tracks are not aligned well, they may be causing the door not to work. It’s not always necessary to unscrew the tracks; you can just try to loosen the bolts or screws and to tap the tracks slightly into position. Use a level to check the alignment of the tracks. Aligned tracks will let you be done with your garage door repair in no time.

3. Clean and Dry the Tracks

Even though it may sound obvious, but hardened dirt and old lubricant may be the cause of the garage door sticking. In this case, your garage door repair may consist of merely cleaning the tracks and then drying them. You can use regular cleaners to clean the tracks.

4. Lubricate the Tracks and the Rollers

Merely lubricating both, the tracks and the rollers, can fix the problem and conclude your garage door repair in no time. For lubrication, you may use a lubricant spray or a silicon spray. It is probably better to lubricate the tracks after cleaning them. Actually, any movable part will benefit from lubrication.

5. Tightening the Loose Bolts and Screws

Bolts and screws tend to become loose with time. Try to check all of the screws and bolts involved in the opening/closing mechanism of your door. Sometimes, merely tightening them may solve the whole problem. If you cannot tighten the screws, because the holes themselves have become loose, then you can use a “wood filler” or pieces of normal wood to fill the holes.

What Not to Do?

If you have tried every one of the above solutions, and none of them have worked, the problem may be the door spring. However, it is advised not to perform your garage door repair if the problem seems to be the spring, especially if it’s a torsion spring. Unfortunately, there have been numerous cases, where people have gotten injured or even killed by the garage door springs. One of the most common injuries is a hit in the head, resulting in serious trauma to the brain.

If you have doubts your garage repair, by no means should you attempt it. It generally will not cost too much. However, a professional will save you from any injuries.

Homebuilder Adam Stranton has done extensive garage door repairs during his career. He also has a solid guide for new garage door prices

Article Source:

I hope you enjoyed this article about San Diego Garage Door Repair

Article Source:
Tagged , , ,

What Makes A Good San Diego Garage Door Repair Company?

San Diego, CA: Garages are an important part of any house. It is actually more than just a place for parking vehicles, and has multiple uses such as storing tools and other frequently used items. A strong and safe garage is necessary as it can be easy to enter a house through the garage. But most people fail to understand its importance and never really care about maintaining and repairing their garage doors, unless it completely stops working. Since garage doors are very big, it poses a greater danger when it is not working properly or malfunctions.

Most people nowadays use automatic garage doors for their convenience. The working of a garage door mainly deals with the rollers, pulleys etc in it. In most cases some debris might have got in between these parts and jamming the movement. Crooked cables, loose springs and cracked pulleys etc should be worked upon only after ensuring safety. The instructions in the manual should not be ignored while working on garage doors as it may result in danger. Care should be taken that power is cut off before attempting any repair on the garage doors.

The garage opener or controller is also another important element that might needs regular maintenance. This includes the fuses switches and power sources. These should be properly checked as they are the primary elements causing the door to open and close. They should be inspected for debris and moisture as well as moisture can lead to short circuiting of the unit. Make sure that the power plugs are properly plugged in etc.

It is best that the garage door services are left to the experts or professionals. Todays garage systems are bit more sophisticated for people to handle by themselves. When selecting a company for garage service, always ensure that they have certified professionals. Round the clock availability of service is another important factor as people may end up with garage issues and too busy to wait. Also ensure that the the team arrives with their service truck with all the tools necessary.

For any garage door repair in San Diego, All American Garage Doors is one of the first names that comes into people’s mind. The company acquired this trust with their consistent hard work and good customer relationships. A locally owned and run company, they treat all their customers with integrity and takes up all jobs from the simplest to the toughest. They have a certified and hardworking team of professionals, who gets the job done quickly and flawlessly. They have a great customer care department as well which provides users with free quotes with just one call.


All American is well known for providing only the highest level of satisfaction to all of thier San Diego customers. They take up any repair service no matter if it’s a garage door spring, motor or door that needs fixing.

For more information on san diego garage door repair and garage door opener repair san diego, please visit:

Garage Door Opener Replacement or Reset?

If you have just bought a new garage door system, have had a break in and want to change the control code for your garage door, or just want to update your system for routine security reasons, you need to program the garage door opener and the remote control. Though there can be some variation with different brands and varieties of garage door, the following is a typical process of reprogramming your remote. This is how you would program the opener and remote on the popular Craftsman garage door system. This type of system is one of the most widely used today.

Make Sure there is Power to the Keypad

Most Craftsman garage door systems have a main wall mounted keypad on which numbers can be entered. The first step is to make sure this keypad has power. It usually only runs on batteries, so make sure that they batteries are fresh and the device is operational.

Get Access to Garage Door Opener Panel

Begin by taking the cover off the back of the garage door opener box. This is the large control box located near the ceiling. It should have a red cover you can simply take off manually to reveal various buttons on the remote. You may need a ladder to climb up and access this panel.

Erase Old Programming

Now you need to erase the existing information on the system. If it is a new system, there may not be any programming on it in the first place. But it is a good idea to go through this step anyway just to be sure.

There should be a large square red button on the back of the remote. It is often situated next to the blue travel and force adjustments on the opener. There should also be instructions printed near these controls.

You may want to take the light bulb that is screwed into to this panel out so that you can access the panel better. However, remember to replace it before the reprogramming step because it indicates successful reprogramming by flashing on and off.

The way to clear the system is to press and hold the red button. When you do this, a small light to the right of the button will light up. Hold the red button down until the light goes out. Once it has gone out, you know that the system has been cleared.

Once you have done this, neither the keypad not the remote will work. The system has been completely cleared of any programmed data, so there is no way for the keypad and remote to communicate with the door opener box. So reprogramming is the next step.

Reprogram the System

The system now needs to be reprogrammed. This is very easily done on a Craftsman system. Simply press the red button once. The light next to it will light up again. You now have about 30 seconds to walk over to the keypad and enter any 4 digit code of your choice. Try not to make it something too obvious or that someone can easily guess. Type in the numbers and then press the enter button.

If the reprogramming is successful, the light on the garage door opener, as noted above, will go off and then come back on. This means you’re all finished with the reprogramming. This is a very “user friendly” type of system, so they have made reprogramming extremely simple.

Set Remote

The only thing left to do is to reset the remote. Like the other steps in the reprogramming process, this is very easy. Climb back up your ladder so you again have access to the remote control box. Now simply press the red button at the same time as pressing the open/close button on the remote, and release them at the same time. Once you have done this, the remote will work to open the garage door.

That’s really all there is to programming or reprogramming a Craftsman garage door system. Again, this is a very easy system for the average user to work with, which may have something to do with its popularity.

Garage Door Repair Requirements

This blog site is about garage door repair needed in San Diego in general. Thus it applies both to fixing various garage door issues yourself and in dealing with repair professionals. You may be unsure as to whether you are handy enough to attempt a certain repair or whether it is a good idea in general. The following are some criteria you can use to judge whether or not you’re the right person for a garage door repair job in San Diego:

Do you have the Tools or Do You Need to Buy Them?

This is a good preliminary evaluation consideration. If you merely need to make some adjustments, tighten screws, and the like, chances are that you do indeed have the tools. Usually all you will need are some wrenches and screw drivers for this type of repair. However, some larger scale repairs may need more extensive or less common tools. For instance, if you want to take dents out of a garage door, you will need a can of liquid carbon dioxide. This can be purchased easily enough but most people don’t have it on hand.

Similarly if you need to replace larger items like the central arm or the garage door opener itself, you will probably need at least a power drill/screw driver. This will speed things up and make taking out and putting in screws easier.

Most people that are relatively handy do have the tools for garage door repair. They are ordinary tools that most people keep in their garage. If not they can be purchased easily enough, so honestly this is not that much of a consideration. However it is a place to start. You may either elect to go out and buy the tools if you do not have them or opt to have someone else do the job.

How Comfortable are you with Repair Jobs?

Most people have some idea of how handy they are. If you don’t think you’re handy at all, however, that may not be a reason not to attempt repairs. There are a number of very simple repairs that can be accomplished by almost anyone. Some examples are adjustments to the travel and force of the door, reprogramming the door opener, and doing simple maintenance such as tightening screws. There is always a first time with repairs, so even if you do not consider yourself especially handy, you an try simple repairs and work your way up to more complicated ones. Think in terms of at least learning about garage door repair rather than having to accomplish everything right off the bat. You may surprise yourself by what you can learn in the process by just giving it a try.

If you consider yourself relatively handy, it then becomes a question of how handy and how much time you want to invest in a project. Once you have done a few home improvement type projects, you tend to see the commonalities between all kinds of different projects. So chances are if you have some experience, many garage door repairs will be well within your reach. You may want to stop short of jobs involving work with electronics, such as replacing the mother board in a garage door opener.

How Comfortable are you with Electricity?

Garage door openers are electrical devices. So they may involve some work with electricity. This is usually not too much of a problem in that most repairs that a homeowner will do are done with the garage door opener box unplugged. But you will need to plug it back in in order to check that it is functioning properly and so on. Most people are fine with doing simple work with electrical wiring and appliances, but if it makes you especially nervous you might want to let someone else do it. Also be sure and observe all safety precautions when dealing with electricity.

Do you have the Time?

A time investment is required to do a job properly. This varies by the job of course, but it still doesn’t hurt to get a sense of how much time you really have to spend on a particular job. You don’t want to rush a job – that can give you poor results and be unsafe. You also will need to read instructions, documentation, and any other informational material you can find. So this is extra time that should be factored into the job as well.

These are some considerations you can use to make sure that you are ready to tackle a certain garage door repair or maintenance job. Be sure and take everything into consideration before attempting a job. Chances are you might be able to handle a garage repair job yourself, but getting a comprehensive sense of your job capability will make you that much more confident and well informed as you actually do the work.

Still not sure? Give a us a call for a no-hassle free quote, then make your decision. (619)356-0186

Garage Door Repair Common Problems

Automatic garage doors are an extremely common feature of the domestic environment these days. When many people think of or encounter a problem requiring garage door repair they assume it is something for which they will have to call a technician or repair professional to come out to the house and service the garage door opener mechanism. While in some cases this will be necessary, there are a number of things you, the garage and homeowner, can probably handle on your own. The following is an overview of the types of problems you might experience with your garage door and some approaches you can take to fixing them.

Before getting too fancy with anything, you should check commonly overlooked and simple causes of your garage door problem, or what might be called problems of the “duh” type. These are things that can result from simple forgetfulness or accidental actions. You would feel very silly if you had a technician come out (and you had to pay for the visit) if any of the following problems were actually the case. So check these types of possibilities before any others:

It’s possible that the garage door opener – the box like mechanism situated near the ceiling which is responsible for opening and closing the door itself – is not plugged in. This can be because someone simply forgot to plug it in, or because it has slipped out of a loose socket. An AC cord usually exits the machine and plugs into an outlet on the ceiling, or perhaps to an extension cord that runs to a wall outlet. Check to see if this is plugged in and you may have the solution to why your door won’t open or close right there.

A side note here is that even if the opener is plugged in you can try unplugging and plugging it in again. This will reset the sensors and this can be part of your problem.

There can be a variety of problems of an electrical nature with garage doors as well. Just one example of this might be, say, wires that have become exposed, broken, or have shorted out. Problems of this may or may not be able to be fixed by a homeowner, but often they can. Many such repairs require only ordinary household items like wire crimpers, electrical tape, wire nuts or wire sleeves, and so on.

Mechanical problems with garage doors and openers are common as well. These can include things like a jammed control arm, stripped plastic gears on the box itself, and problems with latches or locks. Many of these problems can be fixed by replacing a part. How easy this is for a handy homeowner to do is based on the part and the handiness of the homeowner, but there are indeed parts easily available for many commercially easily available garage doors, and many of these are not very hard to install.